Kmc-controls VEZ-4x Series Bedienungsanleitung PDF herunterladen

VEZ-4x Series, 2-Way/3-Way, NPT Zone Control Valves (1/2 to 1") 1 Installation Guide

Installation Guide

2-Way/3-Way, NPT, Zone Control Valves (

⁄2 to 1")

VEZ-4x Series

Mounting Valve Body

1. Clean the lines upstream from the valve. Remove

any debris larger than 0.06" (0.015 mm).

2. Alignthevalve’sowindicatorwiththesystem

ow(seepage4for3-waymixing or diverting

applications).

3. Mountthevalvesotheactuatorispositionedover

valve.

CAUTION

To prevent condensation from dripping onto the

actuator housing, mount the valve with the actuator

in the upright position or, at most, at a 45° angle.

4. Sealvalveswithapprovedpipesealant.

5. Usingtwowrenches,securethevalvetothepipe.

Torqueshouldnotexceed75ft-lbs.(102N

•m).

6. Eliminate air from the system to keep the valves

fullofuidduringoperation.

NOTE: Ifthesystemexperienceslargeamountsof

debris,stepsshouldbetakentokeepthe

systemclean.

Mounting Valve Body 1

Mounting Actuator on Valve Body 1

Wiring 2

Two-Position Spring Return 2

Proportional and Tri-State 2

Manual Override 3

Proportional and Tri-State 3

Two-Position Spring Return 3

Operation 4

Maintenance 4

Select Speciﬁcations 4

More Information 4

Important Notices 4

CAUTION

Using mineral oil lubricants or other incompatible

substances in system ﬂuids may damage EPDM

rubber seals in valves. Before using any lubricant or

additive in a water or ethylene glycol base, consult

the substance manufacturer for compatibility with

EPDM (Ethylene Propylene Diene Monomer).

2-Way with Tri-State or

Proportional Actuator

3-Way with 2-Position

Fail-Safe Actuator

Mounting Actuator on Valve Body

Ring Nut to

Valve Body

Black Plastic

Attachment

Support Ring

CAUTION

If mounting the actuator to a valve already in-line,

close the shut-off valves in the piping (upstream

ﬁrst, then downstream) or switch off the pump to

allow the differential pressure in the valve to drop.

1. Toremoveanexistingactuator,disconnect

thewiring,turntheringnut(couplingpiece)

counterclockwiseuntilitisloose,andpullothe

actuator.

CAUTION

The black plastic actuator attachment support ring

must be in place on top of the valve bonnet before

mounting the actuator or damage to the actuator

connection may result.

2a.ForNOactuators(“A,”“M,”and“P”),placethe

actuatorontopofthevalvebodyandrmly

hand-tighten(only)theringnut.

NOTE: Thelastdigitofvalvemodelnumber

representsthetypeofactuator.

Mounting Actuator on Valve Body

2b. For NC actuators (“B,”“F,” “N,” and “Q”),

manually rotate and latch open the actuator (or

propervalveclose-omaybeaected).Seethe

ManualOverridesectiononpage3.Thenplace

theactuatorontopofthevalvebody,rmly

hand-tighten(only)theringnut,andreturnthe

actuatortoitsnormalposition.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Installation Guide

VEZ-4x Series, 2-Way/3-Way, NPT Zone Control Valves (1/2 to 1") 1 Installation GuideInstallation Guide2-Way/3-Way, NPT, Zone Control Valves (1

Seite 2 - CAUTION

VEZ-4x Series, 2-Way/3-Way, NPT Zone Control Valves (1/2 to 1") 2 Installation GuideGG0(Red Wire)(Black Wire)24 VACNeutralLN(Black Wire)(Whit

Seite 3 - Manual Override

VEZ-4x Series, 2-Way/3-Way, NPT Zone Control Valves (1/2 to 1") 3 Installation Guide(A) Allow handle to turn counterclockwise to extend s

Seite 4 - 34to230°F(1to110°C)

Kommentare zu diesen Handbüchern

Keine Kommentare

Kmc-controls VEZ-4x Series Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Kmc-controls VEZ-4x Series herunter. KMC Controls VEZ-4x Series User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Kmc-controls VEZ-4x Series